Jump to content
RockWare Support Forum

MarkR

Members
  • Content count

    24
  • Joined

  • Last visited

Community Reputation

0 Neutral

About MarkR

  • Rank
    Member
  1. Automate Printing

    Is it possible to automate printing in a RCL file? I want to print a sequence of rk6 drawings, with a vertical exaggeration, and best fit to pdf files.
  2. Multiple Topo Surfaces

    Thanks very much. Is there any way to loop commands (eg For..Next)?
  3. Multiple Topo Surfaces

    I can automate creating the multiple water surface profiles (with no other data) using RCL. So now I have up to eighteen rk6 files, which I want to combine into a single drawing, showing changes in water table over time, with different line colours and types to signify the dates. Is there a way to append rk6 files using a macro/RCL?
  4. Very slow log diagrams

    The creation of log diagrams in a multi-log profile in V15 appears to be very slow. For the same model section w/ 15 logs and one surface, V15 takes 2.5 minutes, while V14 is done in 11s. The information screen indicates that all the time is being taken up in "creating xxx log diagram". Is there any obvious reason for this?
  5. Multiple Topo Surfaces

    Has there been any advance on this in V15? I am again faced with needing to plot multiple surfaces on sections. I can do it the slow way, but was hoping after 3 years there would be something better?
  6. striplog project dimensions

    In Rockworks15: When I create a single striplog: (single multi-log profile), at the bottom of the drawing it says: Project Dimensions - Dynamic Pattern, and the X and Y coordinates make sense and can be used for export as XY values. But when I create additional parallel profiles it says: No project dimensions and the X and Y values appear to be offset, as if they were being plotted all on the same sheet, although I have chosen to "generate individual diagrams". If I load the same project in Rockworks14, I get Project Dimensions - Dynamic Patterns for each created striplog.
  7. Striplog Title Alignment

    In Rockplot2D all my vertically orientated titles were set to base justification, whereas, I would like them to be centered over the log. On the scale I am using, with base justification, the vertically orientated labels all appear to be offset to the left. Can this justification be changed?
  8. Save to Polygon Table Error

    I have drawn a polygon in a rockplot/2D drawing. I select it, then use the right mouse, shortcut menu, to select "save to polygon table". The extra decimal point appears in the second column (Y/vertical) , primarily for values that are negative. I tried to attach examples, but the forum says I am not permitted to upload those kind of files. Also interested if you had any more info on my question on alignment for borehole titles when they are vertical.
  9. Save to Polygon Table Error

    I have been drawing polylines on my 2D drawings in Rockplot/2D (v14). When I chose save to polygon table, everything works, except some of the entries are incorrectly written with two decimal points in the number (i.e. 12..32245)?
  10. When I use the clipping tool in Rockworks2D, only the data is clipped. If I have a background bitmap, this remains the same and the drawing is not reduced. I can clip the background map seperately, but this is a very difficult system as it uses pixels and I am not sure how to match up the pixels with the data area. Is there a way to clip the entire drawing as a whole?
  11. Vertical Exaggeration

    In Rockplot2D is there a way to set the exaggeration, so that when you reopen the drawing it has not reverted to VE=1
  12. Striplog Title Alignment

    What I noticed when I went into Rockplot2D is that all my vertically orientated titles were set to base justification, whereas, I would like them to be centered over the log. On the scale I am using, with base justification, the vertically orientated labels all appear to be offset to the left.
  13. Striplog Title Alignment

    I would like to set the default alignment for borehole titles in the Striplog dialog layout options. I can see how to do this afterwards in RockPlot2D, but this is too time consuming for lots of holes.
  14. Setup data

    Is there a way to reference the setup data into an edit-text tab value? I want to plot the Easting, Northing and RL in the header. It would be nice not to have to type this data in twice. Thanks, Mark
  15. I tried the example polygon.tab file as well as making my own. I get this error: In operator without () in query expression 'NAME IN)' When I look at the SQL statement it has: UPDATE [Location] L SET Enabled = 1 WHERE NAME IN ) It doesn't appear to access the file I put in, although the summary has the file name correctly.
×