steckler

Good morning Paul,, thank you very much for your answer. I tried what you said, but the size remains almost invisible no matter what I do. The legend in 3D is fine but not in 2D output. My colleague follows your recommandation on another project and it works. So i do not know what is wrong for me . I send you screnshots by mail in case you notice something Best regards Mathieu

Good morning, Could you tell me how to increase the size of the text of a legend ? I have just sent you a picture by email Thank you very much for your help Best regards Mathieu

Hi Alison, I have just sent you the picture on tech@rockware.com Thank you very much for your help Best regards Mathieu

Hi, I always strat a project withe creating de XYZ grid for the bathymetry. This time, I got the attached picture and I do not know why the contour lines have this shape and why they are not properly located compare to the color legend. Do you have an idea how to make adjustement ? Thank you very much in advance Best regards Mathieu Nota: can you tell me how to send you the picture. The size is always higer than 15.05kB

Dear Alison, I selected "high fidelity" and indeed it completely solved my problem. Thank you very much again for your precious help. Best regards. Mathieu

Dear Alison, Thank you very much again for your quick detailed answer. I will investigate your advice and come back to you with the results Best regards Mathieu

Good morning, I created a grid which reprensents to top of a geological substratum based on available data from boreholes. I tried all the algorthms (inverse distance, kriging, triangulation etc). When I check at the location of the existing borehole, for all boreholes there are always a difference (minor or major depending on the method). Is there a way to impose at the location of the borehole the value as a true one after interpolation? Thank you very much Best regards Mathieu

Hello Alison, thank you very much for your email. I use Rockworks 2022.3.9 version I used Grid | Filter | Polygon Clip tool and now it works perfectly well. Thanks again for your time. Your software is magic ! Best regards Mathieu

Good morning, I created a 3D model using a polygon filter. I created a bathymetric 3D map using the resample math grid fonction fitting the project dimension. My question is: I would like that the resample bathy fit the polygon countour ? Is it possible ? Thank you for your help Best regards Mathieu

Thank you very much Paul. I will try this tool and come back to you if necessary. Best regards

Good Morning Paul, I would have an addional question. I manange to create a 2D stratigraphy structure grid with a filter polygon. Is it possible to create a table with 200 points (XY coordinates) inside the polygon (corresponding to piles locations) and to obtain automatically the Z elevation of the 200 points? Best regards Mathieu

It works perfectly well. thank you very much for your help. Best regards. Mathieu

Paul, I did something like this. Is it possible to create a "3D polygon" ? Or how should I do to get rid off the additional space (right and left from the rectangle) in my 3D model ?

Good Morning Paul, thank you very wuch for your quick answer. Creating a polygon would perfectly answer my question. Which menu should I select to create it ? Best regards Mathieu

Hello, I would like to know if it is possible to modify the project dimension in order to fit the red rectangle. (Otherwise is it possible to modify North Orientation ?) Thank you very much for your help Best regards Mathieu T

Thank you very much Paul, I have just created a grid model from an ASCII file with YYZ coordinates. It works perfectly.

Hello, I would like to know if it is possible to create several "2D log design" for the same 2D profile. Ex: on a geotechnical profile, I have to draw: * 5 BH with SPT results * 7 CPTS with qc curve * 6 Pressumeter BH with pl and Em curves If I create a single "2D log design" with all the columns (litho, strati, SPT, qc, pl, Em), I will get plenty of emplty columns in the profile. Thank you very much for your help Best regards Mathieu

Hello, I would like to know how to import a bathymetric map and will it be taking into account when creating 2D profiles ? Thank you very much for your help Best regards Mathieu