saeid

Members
  • Content count

    5
  • Joined

  • Last visited

Community Reputation

0 Neutral

About saeid

  • Rank
    Newbie
  • Birthday
  1. Dear all, Is it possible to apply MINC method in Petrasim? It seems we can apply MINC to the entire model, but I want to apply MINC method just to selected number of cells in one layer of the model in vicinity of the fault. Looking forward to hearing from you Thanks Saeid
  2. Thanks for your reply, sent the file. Lookig fw to hearing from you, Regards
  3. When I run my model simulation stops and the error message is Simulation Halted Prematurely: Click to view output file! and "log" tab of running TOUGH2 appears as below, It says "EOS CANNOT FIND PARAMETERS AT ELEMENT * 4321*" when I disable three layers of model it runs!! Tried to attach the file, it says I am not allowed to update this type of file "Petrasim input file" END OF TOUGH2 INPUT JOB --- ELAPSED TIME = 1.8120 SECONDS ( 1, 2) ST = 0.100000E+03 DT = 0.100000E+03 DX1= 0.112726E+06 DX2= 0.315307E-03 T = 25.000 P = 214026. S = 0.000000E+00 ++++++++++ EOS CANNOT FIND PARAMETERS AT ELEMENT * 4321* XX(M) = -0.10305E+06 0.24999E+02 +++++++++ REDUCE TIME STEP AT ( 2, 1) ++++++++++++++++ NEW DELT = 0.500000E+02 ++++++++++ EOS CANNOT FIND PARAMETERS AT ELEMENT * 4321* XX(M) = -0.10091E+05 0.25000E+02 +++++++++ REDUCE TIME STEP AT ( 2, 1) ++++++++++++++++ NEW DELT = 0.125000E+02 ( 2, 1) ST = 0.112500E+03 DT = 0.125000E+02 DX1= 0.000000E+00 DX2= 0.000000E+00 T = 25.000 P = 214026. S = 0.000000E+00 ( 3, 2) ST = 0.137500E+03 DT = 0.250000E+02 DX1= -.183616E+05 DX2= -.506256E-04 T = 25.000 P = 7701. S = 0.000000E+00 ++++++++++ EOS CANNOT FIND PARAMETERS AT ELEMENT * 4321* XX(M) = -0.28008E+05 0.25000E+02 +++++++++ REDUCE TIME STEP AT ( 4, 1) ++++++++++++++++ NEW DELT = 0.125000E+02 ( 4, 1) ST = 0.150000E+03 DT = 0.125000E+02 DX1= 0.000000E+00 DX2= 0.000000E+00 T = 25.000 P = 241653. S = 0.000000E+00 ++++++++++ EOS CANNOT FIND PARAMETERS AT ELEMENT * 4321* XX(M) = -0.10560E+05 0.25000E+02 +++++++++ REDUCE TIME STEP AT ( 5, 1) ++++++++++++++++ NEW DELT = 0.625000E+01 ( 5, 1) ST = 0.156250E+03 DT = 0.625000E+01 DX1= 0.000000E+00 DX2= 0.000000E+00 T = 25.000 P = 241653. S = 0.000000E+00 ( 6, 1) ST = 0.168750E+03 DT = 0.125000E+02 DX1= 0.000000E+00 DX2= 0.000000E+00 T = 25.000 P = 241653. S = 0.000000E+00 ++++++++++ EOS CANNOT FIND PARAMETERS AT ELEMENT * 4321* XX(M) = -0.10560E+05 0.25000E+02 +++++++++ CONVERGENCE FAILURE ON TIME STEP # 7 WITH DT = 0.250000E+02 SECONDS, FOLLOWING TWO STEPS THAT CONVERGED ON ITER = 1 STOP EXECUTION AFTER NEXT TIME STEP +++++++++ REDUCE TIME STEP AT ( 7, 1) ++++++++++++++++ NEW DELT = 0.625000E+01 ( 7, 1) ST = 0.175000E+03 DT = 0.625000E+01 DX1= 0.000000E+00 DX2= 0.000000E+00 T = 25.000 P = 241653. S = 0.000000E+00 END OF TOUGH2 SIMULATION RUN --- ELAPSED TIME = 2.922 SEC-- CALCULATION TIME = 1.110 SEC-- DATA INPUT TIME = 1.812 SEC
  4. Thank you Alison, Regards, Saeid
  5. New to Petrasim, I wanna put let say mass flow rate of 12 kg/s with enthalpy of 1000 Kj/kg (fluid recharge), to one cell in bottum layer of geothermal reservoir. In Tough2 input file we could use MASS function under Gener. Sink/Source function in petrasim has the options of Heat, Production and Injection. Any idea?